Give one known size in the photo — get lengths and angles off the image, with an error bar.
Read this before trusting a number. A photo has no size of its own — a 40 mm part
close to the lens and a 400 mm part far away produce identical pixels. One known reference
fixes the scale, but only for things in the same plane as that reference. Anything nearer
or further than the plane is silently wrong — turn the grid on and check that your target sits
on the reference plane before you use the figure. If what you want to measure simply
stands on the floor at a different distance, use Ground plane mode instead: it handles
any distance and does not care how far away the object is.
1 — Photo open a site photo, then zoom in before you click anything
Open a photo above, drop one here, or paste one with Ctrl + V.
No image
2 — Reference the one thing in the photo whose real size you know
Mark the four corners of the reference.
3 — Measure click point to point; the label follows the line
Set the reference first.
Ref
Length
± estimate
Angle to reference
Note
4 — Take it away marked-up image and a table you can paste
5 — What is valid, and what is not
Flat and Plane modes: same plane only. Every measurement is computed inside the
reference plane. Nothing in the maths can tell that your target is actually nearer or further
— it returns a confident wrong number, and a door in the background measured against a
door in the foreground is the classic case. The grid shows you the plane; use it.
Ground plane mode is the fix for that case. When the objects stand on the same floor,
the horizon plus one known height (or the camera height) gives the height of anything on that
floor at any distance — the distance cancels out of the algebra entirely. It does not need
the object to sit in the reference plane and it does not care how far away it is.
Ground plane mode's own limits. The floor must be flat; the camera must not be rolled
(the horizon must be level in the image) or the single-row assumption breaks; the object must
stand on that floor with its base visible or judgeable. A height comes out proportional to the
camera height, so calibrate on a known height rather than trusting the 1600 mm
default — the default carries its own ±100 mm into every answer.
A tilted camera costs a couple of per cent. The algebra is exact when the camera is
level. Measured on a 2.0 m object with the camera 1.6 m up: 10° of downward tilt
reads +2.4 % at 3 m and +0.8 % at 9 m; 20° reads
+5.1 % and +1.6 %. The error grows with tilt and with how close the object is, and
calibrating on a near object flips the sign so distant ones read slightly low. Either way it is
a couple of per cent — not the tens of per cent that plane mismatch gives you. Shoot level
and it goes away.
Widths are the weaker measurement. A face-on width assumes the surface is square to the
camera, so on a tilted shot the scale drifts across the object's height. Height is the reliable
output of this mode.
The grid is your evidence. In Plane mode the yellow grid is drawn in the reference
plane, so it should lie flat on the photographed surface. If its cells look sheared or
stretched along one side, the Width and Height are the wrong way round (try Swap W ↔ H);
if the grid folds or crosses itself, the four corners were clicked corner-to-corner instead of
going around the edge; if it drifts off the surface, that surface is not flat. Any of those and
the numbers are meaningless.
The building is only a nominal-size reference. An AU brick is 230 × 76 mm
work size (AS/NZS 4455), but bricks vary and the bed joint alone is allowed ±3 mm
(AS 3700) — and 76 mm of reference is a poor lever. A door leaf is nominally
820 × 2040 mm (AS 2688) and makes a far better reference because it is
25 times longer. Two caveats: the visible leaf is slightly under 820 mm once it sits
behind the frame and stop, and a frame opening is not the leaf — 880 × 2100
is typical but it moves with the frame profile, so measure the actual opening if you can.
Mark big. A fixed clicking error over a short reference is a large percentage error
over everything. Use the longest reference that fits the frame, then zoom right in.
Zoom before clicking. At fit zoom on a 4000 px phone photo, one screen pixel is
several photo pixels. The ± column already accounts for this
— it will improve as you zoom in and re-mark.
Lens distortion is not corrected. Wide-angle phone shots bend straight lines near the
frame edges. Keep the reference and the target away from the extreme corners.
Keep the camera settings constant. Zooming the lens between shots changes the
geometry; digital zoom changes nothing but resolution.
Check it. Measure something in the photo you already know the size of. If it does not
come back right, the plane or the reference is wrong.
The ± figures are placement error only — they do not include plane
mismatch, lens distortion or a wrong reference length. They are a floor on the real error,
never a promise.